Ingersoll Rand 2-WTR-E10 20hp (2x10HP) Duplex Oil Free Air Compressor 70cfm 175psi 230v/3ph 120 Gal

$47,439.00
$0.00
SKU: 2-WTR-E10 230v 3Ph
Part #: 2-WTR-E10 230v 3Ph
Call to order 866-203-2944

Ingersoll Rand 2-WTR-E10 20hp (2x10HP) Duplex Oil Free Air Compressor 70cfm 175psi 230v/3ph 120 Gal

The Ingersoll Rand 2-WTR-E10 is a 20hp duplex oil free air compressor that utilizes two 10hp pumps and motors and is mounted on a 120 gallon air receiver. This model operates on 230v 3 phase power. The two 10hp motors combine to make a two stage 20hp oil free air compressor that will displace 70cfm @ 175psi. 

An alternator is pre-installed and wired with the Ingersoll Rand 2-WTR series duplex oil free compressor. The alternator panel allows both compressor motors to operate in response to system air pressure demand. For example, if system pressure dips below the preset lower pressure limit, compressor “A” will automatically start. If pressure rises to the upper set point limit, compressor “A” will shut down. Next time system pressure drops below the preset lower pressure limit, compressor “B” will automatically start. Should system demand require, both compressor units will start automatically to meet and maintain system air pressure demand. 

The 2-WTR-E10 utilizes the WTR45 oilless air compressor pump. This pump has a totally dry crankcase – no oil is used inside of the compression chamber. Therefore the risk of compressor lubricants getting downstream into your production is eliminated. The internal piston rings use an exclusive o-ring bumper to prevent axial movement of the guide rings.

This 20hp oil free compressor is mounted on a 120 gallon horizontal receiver tank. All components are mounted to a spring isolated base. This eliminates the need for additional vibration dampeners as the springs will absorb all vibration from the air compressor.

Since this is an industrial grade three phase oil-free 20hp duplex compressor, two motor starter is pre-installed with the alternator on the outside of the enclosure. These provide full voltage control of the motor. An overload relay is included to protect the motor windings from temperatures rises and motor overloads due to voltage issues.

The entire 2-WTR-E10 compressor assembly is contained in a semi-enclosed cabinet. This cabinet helps to reduce the noise level, increase cooling capacity and helps to protect against dust or debris contaminants.

Since oil free air compressors can run warmer than traditional air compressors, a large copper intercooler is pre-installed to reduce the heat load. The heat is further reduced by the oversized finned cylinders and grooves on the flywheel which flow cooling air across the pump.

To further reduce the heat and moisture load, an air cooled aftercooler is pre-installed on the system. The aftercooler on the WTR-E10 will remove about 60% of the moisture from the air lines. This moisture is then removed by a water separator.

The internal Ingersoll Rand CCN# for this air compressor is CIDVWB07

Ingersoll Rand 2-WTR-E10 - 230v 3 Phase 20HP Oil Free Air Compressor Features:

  • 100% completely oil free air compressor using state-of-the art sealed bearing technology to ensure clean operation
  • Duplex air compressor with two 10hp pumps and motors
  • 230v three phase main drive motors
  • Easy-to-access components for no hassle servicing and maintenance
  • Pre-installed alternator with motor starters and overload protection: 230v three phase
  • Air cooled aftercooler for moisture removal with water separator
  • 120 gallon horizontal air receiver
  • Sound reducing enclosure with dust protection
  • Plated valve plates and reeds of highest grade steel extend operating life and durability.
  • Cantilevered crankshaft design provides superior balance and long life.
  • Eliminates the need for oil change outs saving on costly maintenance and downtime
California Residents: Prop 65 WARNINGS
Products specifications
Drive StyleBelt Drive
Dimensions88 x 57 x 61"H
Connection Size1.25" NPT
Aftercooler CTD20ºF
AvailabilityShips From Manufacturer
Horse Power20
Max Pressure (PSI)175
CFM @ 175 PSI70
Voltage230/3/60hz
PhaseThree
ConfigurationHorizontal
Tank Size120 Gallons
Weight2820 lbs