Portland Compressor
Experience you can depend on
 

Graco LineLazer Line Stripers

Shop

 

 

 

Our Products
 
Line Striper Information
 
More
 
Stuff
 


 

Graco LineLazer Tip Selection Guide

 
LineLazer spray tiup LineLazer RAC 5 SwitchTip
Also see Tip Sizes
 

LineLazer Tip Selection Guide. Sprayer is supplied with tip LL5319. For additional applications, use the tip selection table as follows:

Note: the last three digits (LL5319) of the tip part number identifies the line width and tip orifice (opening).
For example: the line width for tip LL5319 is 4 in. as shown in the table below. The tip orifice for tip LL5319 is .019 in.

LineLazer Tip Selection Table
Tip Size Line Width Used For
221203* 2 inches    Sport court – light film build
LL5213* 2 inches    Sport court – heavy film build
LL5215* 4 inches    Alkyd paints only – light film build
LL5217 4 inches     Alkyd paints only – medium film build
LL5219 4 inches     Alkyd paints only – heavy film build
LL5315 4 inches     Most traffic paints – light film build
LL5317 4 inches     Most traffic paints – medium film build
LL5319 4 inches     Most traffic paints – medium film build
LL5321 4 inches     Most traffic paints – heavy film build
LL5323 4 inches     Most traffic paints – heavy film build
LL5327† 4 inches    Most traffic paints – heavy film build
LL5417# 4 – 8 inches All paints and high solids traffic paints – light film build
LL5419# 4 – 8 inches All paints and high solids traffic paints – medium film build
LL5421# 4 – 8 inches All paints and high solids traffic paints – heavy film build
LL5621 8 – 12 inches All traffic paints – light film build
LL5623 8 – 12 inches All traffic paints – medium film build
LL5625 8 – 12 inches All traffic paints – medium film build
LL5627 8 – 12 inches All traffic paints – heavy film build
* May require 100 mesh filter to minimize tip plugging.
† Best for use with LineDriver.
# Best for cold weather applications.

How to Maximize Line Quality and Reduce Tip Wear.
Observe the following suggestions to increase line quality and minimize sprayer tip wear.

  • Select a larger tip orifice and run the sprayer at a reduced operating pressure.
  • Running larger tip sizes (example: use tip LL5321 @ 2000 psi instead of LL5317 @ 3300 psi) will significantly increase tip life and reduce tip plugging. It will also produce a more uniform film build across the line.
 
 
Graco LineLazer RAC 5 SwitchTips Click to Order
Graco LineLazer spray tips These yellow tips are specifically designed for line stripping machines. Creates clean, laser-sharp lines with no fuzzy edges. Sprays heavy water-based to thin alkyd traffic paints. Fits the orange RAC5 tip guard.
LL5 and tip size - LL5xxx such as LL5319. Fits RAC 5 Guard (aka RAC V) and RAC IV too.
  Orifice size - inches (thousandths)
Fan Size .013 .015 .017 .019 .021 .023 .025 .027 .029 .031 .033 .035 .039 .055
2 213 215 217 219                    
4   315 317 319 321 323 325 327 329 331 333 335   355
4-8     417 419 421 423 425 427 429 431   435    
8-12         621 623 625 627 629 631   635 639  
 
Flow Rate (gpm) .18 .24 .31 .38 .47 .57 .67 .77 .90 1.03 1.17 1.31 1.63 3.25

Water @ 2000 psi (138 bar, 13.8 MPa) - paints with a higher viscosity will decrease the flow rate
Example: for a tip with a .015 orifice and a 6 in (152 mm) pattern, order LTX315
   
Our most popular tip sizes based on sales are:
 
Sprayer Cleaning | Maintenance | Airless Troubleshooting | Safety
Graco Airless Parts | Airless Accessories | Magnum Parts | Magnum Accessories
FAQ | Tip Sizing | Tip Sizes | Tips on tips | RAC X Tips | Spraying Techniques | Glossary